PIC18F66K80 FAMILY
DS39977F-page 168
2010-2012 Microchip Technology Inc.
10.6
INTx Pin Interrupts
External interrupts on the RB0/INT0, RB1/INT1,
RB2/INT2 and RB3/INT3 pins are edge-triggered. If the
corresponding INTEDGx bit in the INTCON2 register is
set (= 1), the interrupt is triggered by a rising edge. If
that bit is clear, the trigger is on the falling edge.
When a valid edge appears on the RBx/INTx pin, the
corresponding flag bit, INTxIF, is set. This interrupt can
be disabled by clearing the corresponding enable bit,
INTxIE. Before re-enabling the interrupt, the flag bit
(INTxIF) must be cleared in software in the Interrupt
Service Routine.
All external interrupts (INT0, INT1, INT2 and INT3) can
wake up the processor from the power-managed
modes, if bit, INTxIE, was set prior to going into the
power-managed modes. If the Global Interrupt Enable
bit (GIE) is set, the processor will branch to the interrupt
vector following wake-up.
The interrupt priority for INT1, INT2 and INT3 is
determined by the value contained in the Interrupt
Priority
bits,
INT1IP
(INTCON3<6>),
INT2IP
(INTCON3<7>) and INT3IP (INTCON2<1>).
There is no priority bit associated with INT0; it is always
a high-priority interrupt source.
10.7
TMR0 Interrupt
In 8-bit mode (the default), an overflow in the TMR0
register (FFh
00h) will set flag bit, TMR0IF. In 16-bit
mode, an overflow in the TMR0H:TMR0L register pair
(FFFFh
0000h) will set TMR0IF.
The interrupt can be enabled/disabled by setting/clearing
enable bit, TMR0IE (INTCON<5>). Interrupt priority for
Timer0 is determined by the value contained in the inter-
rupt priority bit, TMR0IP (INTCON2<2>). For further
details on the Timer0 module, see Section 13.0 “Timer0
.
10.8
PORTB Interrupt-on-Change
An input change on PORTB<7:4> sets flag bit, RBIF
(INTCON<0>). The interrupt can be enabled/disabled
by setting/clearing enable bit, RBIE (INTCON<3>), and
each individual pin can be enabled/disabled by its
corresponding bit in the IOCB register.
Interrupt priority for PORTB interrupt-on-change is
determined by the value contained in the interrupt
priority bit, RBIP (INTCON2<0>).
REGISTER 10-20: IOCB: INTERRUPT-ON-CHANGE PORTB CONTROL REGISTER
R/W-0
U-0
IOCB7(1)
IOCB6(1)
IOCB5(1)
IOCB4(1)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7-4
IOCB<7:4>:
Interrupt-on-Change PORTB Control bits(1)
1
= Interrupt-on-change is enabled
0
= Interrupt-on-change is disabled
bit 3-0
Unimplemented:
Read as ‘0’
Note 1:
Interrupt-on-change also requires that the RBIE bit of the INTCON register be set.
相关PDF资料
PIC24F32KA302-I/ML MCU 32KB FLASH 2KB RAM 28-QFN
PIC18LF45K80-I/ML MCU PIC ECAN 32KBFLASH 44QFN
PIC18F4221-I/PT IC PIC MCU FLASH 2KX16 44TQFP
PIC18F1320-I/SO IC MCU FLASH 4KX16 A/D 18SOIC
PIC18LF2321-I/SS IC PIC MCU FLASH 4KX16 28SSOP
PIC16F917-I/PT IC PIC MCU FLASH 8KX14 44TQFP
PIC18F1320-I/SS IC MCU FLASH 4KX16 A/D 20SSOP
PIC24FV32KA301-I/P MCU 32KB FLASH 2KB RAM 20-PDIP
相关代理商/技术参数
PIC18F45K80-I/P 功能描述:8位微控制器 -MCU 32KB FL 4KBRM 16MIPS 12bit ADC CTMU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F45K80-I/PT 功能描述:8位微控制器 -MCU 32KB FL 4KBRM 16MIPS 12bit ADC CTMU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F45K80T-I/ML 功能描述:8位微控制器 -MCU 32KB FL 4KBRM 16MIPS 12bit ADC CTMU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F45K80T-I/PT 功能描述:8位微控制器 -MCU 32KB FL 4KBRM 16MIPS 12bit ADC CTMU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F4610-E/ML 功能描述:8位微控制器 -MCU 64KB 3968 RAM 36 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F4610-E/P 功能描述:8位微控制器 -MCU 64KB 3968 RAM 36 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F4610-E/PT 功能描述:8位微控制器 -MCU 64KB 3968 RAM 36 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F4610-I/ML 功能描述:8位微控制器 -MCU 64KB 3968 RAM 36 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT